Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,761. Welcome to our newest member, Bruno
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > Lindsay AirGraver Info - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 11-02-2019, 08:26 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default background removing

I like a dental rotary for background, inlays and undercutting rather than a flat graver. Combines several steps in one. With rotary you can remove background and stipple in the same step. After lowering an area I'm just bouncing on the bottom to resemble stippling. It will look matted after blackened. In the early 80s I was using a dental handpiece that was made by Buffalo Dental. I then used a NSK Presto. The one I use now is BenchJewel Rotary that is on the site: https://www.benchjewel.com/rotary.htm

__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
  #2  
Old 11-03-2019, 07:26 AM
SEngraver SEngraver is offline
Platinum
 
Join Date: Sep 2008
Location: UK.
Posts: 3,484
Default Re: background removing

Hi
Thank for the clip Steve.
SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M.
Reply With Quote
  #3  
Old 11-03-2019, 02:11 PM
JJ Roberts's Avatar
JJ Roberts JJ Roberts is offline
Platinum
 
Join Date: Apr 2006
Location: Northern Virginia
Posts: 2,070
Default Re: background removing

I use a single point 90 degree graver to remove the background,one slip with a rotary tool and you'll have a big problem. J.J.
Reply With Quote
  #4  
Old 11-03-2019, 07:03 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: background removing

Hi JJ, Yes, you need to be careful or you can wipe something out quick.
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
  #5  
Old 11-03-2019, 08:14 PM
JJ Roberts's Avatar
JJ Roberts JJ Roberts is offline
Platinum
 
Join Date: Apr 2006
Location: Northern Virginia
Posts: 2,070
Default Re: background removing

Steve,Thanks I'm not in a rush plus I don't trust myself with a rotary tool and will stay with single point graver. J.J.
Reply With Quote
  #6  
Old 11-05-2019, 01:44 AM
-Daniel- -Daniel- is offline
Steel
 
Join Date: Dec 2018
Location: Germany
Posts: 54
Default Re: background removing

Hi Steve,

thank you for the video!

What kind of tip hast the burr you are using? In the video it looks like a fine but round tip, is that right? I cant see sharp edges or teeth, how could this remove metal then?
Reply With Quote
  #7  
Old 11-05-2019, 02:24 AM
Elmer Elmer is offline
Steel
 
Join Date: Dec 2012
Location: Western Alaska
Posts: 24
Default Re: background removing

Steve,
I have the same rotary tool, i know some dentists here in my small Alaskan town and scored a bunch of carbide burs of various shapes and i am well pleased with the delicate control that it delivers...
I am curious though ... what bur was that you were using? the convex tip shape seems handy.
Reply With Quote
  #8  
Old 11-05-2019, 08:54 AM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: background removing

It is a worn carbide bur that I'm regrinding. Hold it against a diamond bench stone while it is spinning to grind to point. Then put your finger on the point so it can't spin and grind random facets on it. You'll see during the video I stop several times and ground another flat. Once at around frame 3:37 For that area it was a little small and not cutting very fast. I'm just reaching to the bench while holding it from spinning and grind another flat on it. It is on a 2000 diamond bench stone. You can adjust the size of it this way too. When too fat for the area grind it while it is spinning again. After placing a flat on see how it is cutting and if not well, put another on until it does and is the size needed.

Also at around 0:47 I reached over and ground another facet.
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
  #9  
Old 11-05-2019, 01:18 PM
-Daniel- -Daniel- is offline
Steel
 
Join Date: Dec 2018
Location: Germany
Posts: 54
Default Re: background removing

Thank you for your answer, Steve!

So it is like a diamond shape then? I will try this.

Do you have plans to add some further videos? It would be nice to see a inlay or sculpting video
Reply With Quote
  #10  
Old 11-05-2019, 01:22 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: background removing

Hi Daniel, It is all shapes. In other words it is a little different shape each grind with random facets. If it doesn't cut put another on until it does.
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
  #11  
Old 11-24-2019, 10:19 PM
schoggi schoggi is offline
Copper
 
Join Date: Feb 2007
Location: switzerland
Posts: 8
Default Re: background removing

Any chance to have a close up pick or drawing of that point??
sorry for my bad english, an image would make things much clear
thanks in advance
__________________
www.martiquot.com
Reply With Quote
  #12  
Old 11-25-2019, 03:42 PM
Dave London's Avatar
Dave London Dave London is offline
Platinum
 
Join Date: Apr 2006
Location: Colorado Springs
Posts: 2,360
Default Re: background removing

MTC
As Steve stated really no particular point, however a shape like a common screw driver or a 4 corner point like the fixture Tim Wells sells work fine. You can find Tim’s fixture a the bottom of the template page,I think maybe Steve can give you a link
Reply With Quote
  #13  
Old 11-25-2019, 08:27 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: background removing

Quote:
Originally Posted by schoggi View Post
Any chance to have a close up pick or drawing of that point??
sorry for my bad english, an image would make things much clear
thanks in advance
Hi, The shape changes each time. I don't even look at it to see the current shape. From one random grind to the next time I grind another facet it is different.
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 02:56 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.