The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,761. Welcome to our newest member, Bruno
EngravingForum.com -
Domain since Feb 7, 2003
Graver Video Conferencing is empty Join now!
|
ENGRAVING TOOLS - Paypal accepted | Classes | Glossary | Feedback | Tips | Sharpening | Bulino | Videos | Forum Policies |
|
Thread Tools |
#1
|
|||
|
|||
Extra Negativ which makes it Positive
Extra negative is the one that I got help from Steve to develop, which I use
to engrave text inside the rings So now I can finally use Carbide to do this. Also found another use for it, as I show in the video I have done. please bear with my Swenglish :-) Here I show how to grind with the extra Negative Temple Start by marking the graver at 5/8 or 16mm I start to grind the sides At the mark you made, remember that stone height should be 3/4" Grind equally on both sides so you can achieve (about) 0.005 "or 1,27mm Then proceed to do the negative relief, point. Take a little on each side at a time Until you achieve this result Turn it over and continue, being careful not to break the graver by pressing the wrong place Grind until you achieve a thickness of 0.047"or 1.2mm Then switch to the bigg temple, and start to grind the face And end with making the heels of the length that suits you best. I usually do my 0.006"or 0.15mm long Finally, round off the little behind where you grind so it will not be sharp for the fingers Bottom view |
#2
|
||||
|
||||
Re: Extra Negativ which makes it Positive
All i get when I click on the item is "Invalid Attachment" ???
__________________
TOLERANCE is the virtue of a man without convictions. |
#3
|
|||
|
|||
Re: Extra Negativ which makes it Positive
Hi
Me too ,I get the same ,but its mentioned to inform the administrator. What is the "V" angle on it ? SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M. |
#4
|
||||
|
||||
Re: Extra Negativ which makes it Positive
Hi Crazy Horse and SE,
Joacim emailed the photos and I placed them on the server. They should be working now. Thanks again Joacim!
__________________
__________________________________ Steve Lindsay AirGraver.com EngravingArtist.com |
#5
|
|||
|
|||
Re: Extra Negativ which makes it Positive
a fabulous tutorial . even without text, the fotos clearly show how to achieve your grind. i would think this to be quite valuable to many engravers. thank very much for taking the time to share this !!!!!!!
|
#6
|
|||
|
|||
Re: Extra Negativ which makes it Positive
My first youtube video, hope you can stand my Swenglish :-)
It shows what you can use to engrave with it Please experiment with the temple, so perhaps you will find something that is not I done. https://youtu.be/s_ugTrjBLnY |
#7
|
|||
|
|||
Re: Extra Negativ which makes it Positive
Quote:
What is the "V" angle on the template ? SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M. |
#8
|
|||
|
|||
Re: Extra Negativ which makes it Positive
Sorry SE if I do not understand what you mean, but v-angle be made on the tip is 96 degrees if that's what you think.
|
#9
|
|||
|
|||
Re: Extra Negativ which makes it Positive
Quote:
Thats the one,thank you. SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M. |
#10
|
|||
|
|||
Re: Extra Negativ which makes it Positive
the video is very good. it shows a great possibility for those wanting to do inside rings. thanks for taking time to show this.
|
#11
|
|||
|
|||
Re: Extra Negativ which makes it Positive
Hi Joacim,
I would like to ask can one use Jocim's small template on 1/2" bench-stone height to taper the sides of gravers, if yes the template can put straight left and right side on the graver? SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M. |
#12
|
|||
|
|||
Re: Extra Negativ which makes it Positive
Hi Joacim
I have seen in the video it takes the corners off at 3/4" assuming it will do the same at 1/2" I have requested for one. SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M. |
#13
|
|||
|
|||
Re: Extra Negativ which makes it Positive
Hello Joacim, Thanks for this graver as I have begun experimenting with it and I like the control you get with it for inside rings. It takes a little getting used to because of being used to holding the graver in a higher angle but with a bit of practice it is another great tool in the arsenal.
Thanks again, Rod |
#14
|
|||
|
|||
Re: Extra Negativ which makes it Positive
I do not quite understand what you mean SEngraver?
But you can not use the 1/2 height, to get the sides tapperd. it must be 3/4. You will understand when you try. Rodsta I'm glad to hear that you like it. it offers many new opportunities. But the most happy I am to have a Carbide graver that works for engraving inside the rings nowadays, this temple makes it possible. |
#15
|
||||
|
||||
Re: Extra Negativ which makes it Positive
Very interesting! :-) Looks handy for some watch curves as well, where the curve goes up close to the crone. :-)
__________________
https://www.facebook.com/EngraverHand |
Bookmarks |
Tags |
extra negative, inside ring |
Thread Tools | |
|
|